Good quality river water spring water Jiangmen Angel mineral water 8000~ 10000LPH RO water treatment plant

Specifications

1.8000~ 10000LPH RO water treatment plant
2.Capacity: 3000LPH~100000LPH
3.Reverse osmosis, ISO, SS,DOW
4.Simens PLC

Good quality river water spring water germ-free Jiangmen Angel 8000~ 10000LPH Drinking water RO water treatment plant

   

RO water purification system / treatment plant /  mineral water purificaion system / drinking water purification system/ pure water treatment system / water purifier / for drinking/potable water. Our plant could make drinking water, mineral water and pure water from the water sources: Undergound, spring, well, river, borehold, brackish, sea water and etc.

 

 The system adopts automatic design which could make Mineral water/Drinking water/Pure water and monitor the water quality easily, meeting WHO standard and specific country standard.

 

1. The RO water treatment plant process

Raw water→Raw water tank → Raw water booster pump→Mechanical filter (Quartz sand filter)→Activated carbon filter →Precise filter →High-pressure pump →Reverse Osmosis Components→Pure water tank

 

 

2. The 250~ 5000LPH models shown as below: 

 

Model No.	Capacity    (M3/H)	Power (kw)	Recovery Rate (%)	Total land area        LX W X H (mm)
RO-250	0.25	1.5	50	2500X1000X2800
RO-500	0.5	1.5	50	2500X1000X2800
RO-1000	1	2	50	3500X1200X2800
RO-2000	2	4	50-60	6500X1500x2800
RO-3000	3	4.5	55-65	7500X1500X2800
RO-4000	4	6.5	55-65	7500X1500X2800
RO-5000	5	11	60-70	10000X2500X3500
RO-6000	6	11	60-70	10000X2500X3500
RO-8000	8	18	60-70	10000X3500X3500
RO-10000	10	20	60-70	10000X4000X3800
RO-20000	20	30	70-75	15000X5000X5000
RO-30000	30	40	70-75	20000X6000X5000
RO-50000	50	50	70-75	30000X8000X5000

 

♦  Remark: Please kindly email us for the large model from 6,000LPH up to 50,000LPH.

Thank you very much. 

 

 

3. The main struction of the plant

 

Quartz sand filter & Activated carbon filter as pre-treatment

Pre-treatment is important when working with RO and nanofiltration (NF) membranes due to the nature of their spiral wound design. The material is engineered in such a fashion to allow only one way flow through the system. As such the spiral wound design doesn't allow for backpulsing with water or air agitation to scour its surface and remove solids. Since accumulated material cannot be removed from the membrane surface systems they are highly susceptible to fouling (loss of production capacity). Therefore, pretreatment is a necessity for any RO or NF system. Pretreatment in SWRO system has four major components:

• Screening of solids: Solids within the water must be removed and the water treated to prevent fouling of the membranes by fine particle or biological growth, and reduce the risk of damage to high-pressure pump components.
• Cartridge filtration - Generally string-wound polypropylene filters that remove between 1 - 5 micrometre sized particles.
• Dosing of oxidizing biocides such as chlorine to kill bacteria followed by bisulfite dosing to deactivate the chlorine which can destroy a thin-film composite membrane. There are also biofouling inhibitors which do not kill bacteria but simply prevent them from growing slime on the membrane surface.
• Prefiltration pH adjustment: If the pH, hardness and the alkalinity in the feedwater result in a scaling tendency when they are concentrated in the reject stream, acid is dosed to maintain carbonates in their soulble carbonic acid form.
• Carbonic acid cannot combine with calcium to form calcium carbonate scale. Calcium Carbonate Scaling tendency is estimated using the Langelier Saturation Index. Adding too much sulfuric acid to control carbonate scales may result in calcium sulfate, barium sulfate or strontium sulfate scale formation on the RO membrane.

High pressure pump

The pump supplies the pressure needed to push water through the membrane, even as the membrane rejects the passage of salt through it. Typical pressures for range from 225 to 375 psi (1.6 to 2.6 MPa). In the case of seawater, they range from 800 to 1,180 psi (6 to 8 MPa).

 

Membrane assembly

The membrane assembly consists of a pressure vessel with a membrane that allows feedwater to be pressed against it. The membrane must be strong enough to withstand whatever pressure is applied against it. RO membranes are made in a variety of configurations, with the two most common configurations being spiral-wound and a hollow-fiber.

 

Disinfection

Post-treatment consists of stabilizing the water and preparing for distribution. Desalination processes are very effective barriers to pathogenic organisms, however disinfection is used to ensure a "safe" water supply. Disinfection (sometimes called germicidal or bactericidal) is employed to kill any bacteria protozoa and virus that have bypassed the desalination process into the product water. Disinfection may be by means of , using UV lamps directly on the product, or by chlorination or chloramination (chlorine and ammonia). In many countries either chlorination or chloramination is used to provide a "residual" disinfection agent in the water supply system to protect against infection of the water supply by contamination entering the system.

 

     

 

  

 

 

The feature of RO water purification system

1). Water Treatment Plant based on the customer's raw water and output water quality.

2). Reliable vendors like DOW, HYDRANAUTICS, GRUNDFOS and etc.

3). We have professional technician to design the plant.

4). Good after-sales service and technical support

5). Stable work status for daily production

6). Little maintain work

7). Easy operation

 

4. Seaworthy packing: 

  

 

5. Long term business Service: 

•One year warranty for the whole system .

• Free equipment installation and debugging.

• After one year , we can help you to maintain the machine and the accessories are provided only one the cost price.

• Every 3 year , we can help to overhaul the machine freely(labor).

• We can provide internship service and help you train the operator and mechanic.

• Free production technology and process configuration.

• We can help you to design the product line , workshop and provide turn-key project.

 

 

 

6. Easy to Contact us:  

 

  I.  Been in water business since 1998. Have many projects all over the world: Malaysia, Philippine, Australia, Canada, USA, Columbia, Cuba, Chile, Bolivia, Ghana, South America, Kenya, Congo, Uganda, Tanzania, Nigeria, Libya,  UAE, Saudi Arabia, Iran, Iraq, Yemen,  Kazakhstan, Russia and many other small countries.

 

II.  Our professional engineers  will go to help you to install the plant and make you earn money. 2 or 3 engineers will service you. Depends on the capacity of the plant. About 25~ 35 days. 

 

 

There will be more project pictures can be shown to you if you come to visit us. 

 

(1)Electrical box

 

    

 

 

(2) Company picture and container loading outside the warehouse 

   

 

(3) Work house in the real field

    

 

 

  Jiangmen City, Guangond provice

1.5 hour from the fair by car

2 hours from the Guangzhou Baiyun International Airport by car

 

Please Kindly add my following messenger: 

 

   skype: tammyling0505  

 

  Wechat, Whatsapp& cell: 0086- 15917308495