Newest Patent Ultra-low Noise Yellow Silicone Air Dispenser Gun

Specifications

silicone air despenser gun
1.Smooth and uniform
2.Lower noise
3.Unique instant dump valve, non-drip
4.Ergonomically design

Brief Introduction                                                 

 

Name: Newest Patent Ultra-low Noise Yellow Silicone Air Dispenser Gun

 

This air caulking gun is a professional caulking tool and it is designed and developed by the professional group. You can work with less force by this new model high-efficiency caulking gun and do a wonderful work with it.

 

This type of air caulking gun is suitable for DIY and professional use, suitable for 310ml cartridge or 600ml sausage glue. It is widely used in building decoration, electronic appliances, motor vehicles and parts, ships, container industries and so on.

 

When using the powered caulking gun , an air compressor is needed. Small air compressor is ok.

 

 

Features                                                                

 

 

1, make the silicone sealant more smooth and uniform, save time and labour.

2, the silicone sealant flowing can be adjusted by the regulator, more intuitively, easier to understand and safer.

3, unique instant dump valve, non-drip.

4, with silencer inside, there would be very few noise.

5, streamline-designed handle, ergonomically designed and offers a comfortable feeling, easier for continuous operation.

 

 

Directions                                                              

 

1, Pierce or cut off the front tip of the cartridge, remove the front cap from the applicator and insert

the cartridge into the barrel.

Tighten the front cap to provide an air-tight seal between the rear part of the cartridge and the     rubber washer.(Note: Air leaks may occur if the cartridge edge is damaged).

2, Connect the air caulking gun to the air hose then connect with the gas source equipment(air compressor).

3, Adjust the air regulator to a appropriate pressure; we suggest 0.2Mpa.

4, by pulling the trigger, a cushion of the compressed air builds up inside the applicator to initiate the flow of sealant.

5, on releasing the trigger, the sealant flow ceased as the compressed air escapes rapidly with less noise at the rear part of the gun.

6, Rotate the regulator knob clockwise will increase the flow of sealant, and rotate the regulator knob anti-clockwise will reduce the flow of the sealant.

7, always disconnect the air hose after use or when replacing the air hose.

8, front caps should always be securely tightened during using to ensure safety.

9, clean up all the leftovers inside the barrel or outside the barrel after using

 

 Caution                                                                 

 

 1, make sure the front cap is securely tightened before using.

 

2, always disconnect the air hose after using or when replacing silicone sealant.

 

3, the air pressure connected to the applicator should not exceed 0.8Mba to avoid damaging the applicator or any danger.

 

4, don't take apart the parts without any guide.

 

5, don't aim the barrel at people or animals when pulling the trigger.

 

6, it is recommended that safety spectacles are worn when using all pneumatic tools.

 

 

 

Disclaimer                                                             

 

 

 

Considering the various aspects, we can not guarantee this instruction has included all the possible cases. Pls make sure to read the instruction first and under special guidance for the first use. We will not bear the responsiblity for misused or abused.

 

About Us                                                                

 

 

 

Our Patent                                                             

 

  

 

Other Series                                                          

 

 

 

 

Why choose XDLY Hardware                                

 

A.Professional Manufacturers of caulking guns,Foam gun; With 17 years experience to guarantee the quality.

B.Use good materials,we know the guns well.

C.Strict quality control and good mould we use.

D.ISO9001:2000 manage certifications.

E:17 years warranty.Our products have been sold to many countries, such as USA,UK,France,Austrilia,Chile

F:Successful Cases:

1.We are the OEM supplier of New Born Brothers in USA,which is the professional producer of caulking gun.

2.Our customers are as below:Home Depot;Walmart;Blinky;HB TOOLS; YATSAL;Leader-art;Home Center;Mantools;Starfer and so on.