High quality hair removal,anti-Wrinkle, IPL beauty machine(CE approved)

Brief Introduction about IPLSystem

IPL (Intense Pulsed Light) is a kind of light with high energy and broad wavelength, within the range from 530nm to 1200nm. Photothermic and photochemical action will be triggered by the radiation of IPL. On one hand, IPL will promote collagen reproducing and recombining which makes the skin more flexible and smooth. On the other hand, the light with long wavelength can easily pass through epidermis layer and will be absorbed selectively in priority by pathological pigments which will be destroyed by high heat, and get the effect of remove pigmentations, vascular lesions and unwanted hair.

Technique Specification

Light source type:IPL xenon lamp

Light Energy: 15-50J/cm2

Pulse Amount: 1-6

Pulse width: 0.1ms-30 ms

Pulse delay: 0.1ms-100ms

Cooling: internal circulating water + cooling + wind cooling + semiconductor cooling

Safety protection: Impedance test

Spot Size : 8×40mm2

N.W.: 25kg

Dimension: 430mm×470mm×460mm

Voltage: 230V±10%, 50~60Hz

Standard Treatment Process

2.1 Form filling

Fill in the blanks of the Client File, confirm the treatment program, and remind the client pay attention to some points before and after treatment.

2.2 Face cleaning

Clean the face with gentle face cream for 3 minutes.

Remind: clean the hands of operator and the handpiece with

bromogeramine.

2.3 Preheating

Start the equipment after face cleaning; preheat for not less than 3

minutes (without lighting the xenon lamp).

2.4 Shaving

Standard Treatment Process

2.1 Form filling

Fill in the blanks of the Client File, confirm the treatment program, and remind the client pay attention to some points before and after treatment.

2.2 Face cleaning

Clean the face with gentle face cream for 3 minutes.

Remind: clean the hands of operator and the handpiece with

bromogeramine.

2.3 Preheating

Start the equipment after face cleaning; preheat for not less than 3

minutes (without lighting the xenon lamp).

2.4 Shaving

Shave the unwanted hair of the treatment area(2 minutes).

2.5 Gel coating

Coating the gel evenly (2-3mm) on the skin.

Effect:light guide, cooling, anaesthetisin.

Attention: no coating on eyes, eyebrows, lips.

2.6 Eye protection

Operator: wear the safety goggles.

Patient: close the eyes, wear professional safety goggles or cover the eyes with eye patch.

2.7 Allergic test

Emit 2 or 3 light spots in the bottom of ears in safe parameter, observe for 3 minutes.

Effect: do not continue to operate if there is an allergic phenomenon.

2.8 Operation

Carry on the operation with a suitable parameter to the patient.

Attention:

2.8.1 Inform the patient that there will be a slight pricking in operation before operating, to avoid panic.

2.8.2 Start the operation with a low energy grade; adjust the parameters in operating while asking the feeling of the patient.

2.8.3 Move the light spot by one spot overlapping the upper 1/3 part of the previous spot.

No emittng one area repeatedly, otherwise may cause inflaming or burns.

2.8.4 The handpiece should touch the skin vertically, no over pressing or leaving the skin.

2.8.5 Observing the reaction of skin while operating.

2.9 Cold compress

Keep gel coating for 20 minutes after operation ending; carry out cold compress in obvious slight reddish reaction till reddish fading away.

2.10 Cleaning

Clean the gel with cold water, coat corresponding cosmetics.

2.11 Treatment Course

Skin Rejuvenation Program: 30-45 days/time   (4 times/course)

Hair Removal Program: 2-3months/time      (3times/course)

2.12 Special reminding

2.12.1 Ask the client before treatment: is there a allergic or not; is there a bad reaction before for similar operation; fill the Client File concretely. Adjust the parameters on the basis of full acquaintanceconcretely. Adjust the parameters on the basis of full acquaintance of the condition of patient. Inform the patient the possiblereaction inoperation before operating.

2.12.2 In large area treatment or long time continuous operating, the water inside the equipment will warm up and the handpiece will be hot, interrupt the operation to refresh the water or leave the water cool down to continue operating.

2.12.3 Refresh the circulating water in one month; use purified water or medical distilled water.

welcome your enquiry