Home > Products > servo motor > 750w universal ac servo drive ASD-B2-0721-B/ECMA-C20807R6 3000rpm 80mm 2.39nm delta/panasonic servo motor

Share|

750w universal ac servo drive ASD-B2-0721-B/ECMA-C20807R6 3000rpm 80mm 2.39nm delta/panasonic servo motor

FOB Price:Negotiable |Get Latest Price
Min.Order Quantity:1 Piece / Pieces
Supply Ability:100 Piece / Pieces per Month

Product Description

Servo Driver Data

ASDA-B2 Series			100w	200w	400w	750w	1kw	1.5kw	2kw	3kw
			01	02	04	07	10	15	20	30
Power Supply	Phase / Voltage		Three-phase 170 ~ 255 VAC , 50/60 Hz ±5%						Three - phase 170 ~ 255 VAC, 50 / 60 Hz
			Single-phase 200 ~ 255 VAC , 50/60 Hz ±5%
	Input Current (3PH) (Units: Arms)		0.7	1.11	1.86	3.66	4.68	5.9	8.76	9.83
	Input Current (1PH) (Units: Arms)		0.9	1.92	3.22	6.78	8.88	10.3	-----	----
	Continuous Output Current (Units: Arms)		0.9	1.55	2.6	5.1	7.3	8.3	13.4	19.4
Cooling System			Natural Air Circulation				Fan Cooling
Encoder Resolution			17-bit (160,000 p/rev)
Main Circuit Control			SVPWM (Space Vector Pulse Width Modulation) Control
Control Mode			Auto / Manual
Regenerative Resistor			None		Built-in
Position Control Mode	Max. Input Pulse Frequency		Transmitted by differential: 500 K (low speed) / 4 Mpps (high-speed) Transmitted by open-collector: 200 Kpps
	Pulse Type		Pulse + Direction, A phase + B phase, CCW pulse + CW pulse
	Command Source		External pulse
	Smoothing Strategy		Low-pass filter
	E-gear Ratio		Electronic gear N/M multiple N: 1 ~ (226 -1) / M: 1 ~ (231 -1) (1/50
	Torque Limit Operation		Set by parameters
	Feed Forward Compensation		Set by parameters
Speed Control Mode	Analog Input Command	Voltage Range	0 ~ ±10 VDC
		Input Resistance	10 KΩ
		Time Constant	2.2 μs
	Speed Control Range*1		1:5000
	Command Source		External analog signal / Internal parameters
	Smoothing Strategy		Low-pass and S-curve filter
	Torque Limit		Set by parameters or via analog input
	Bandwidth		Maximum 550 Hz
	Speed Accuracy *2		±0.01% at 0 to 100% load fluctuation
			±0.01% at ±10% power fluctuation
			±0.01% at 0 oC to 50 oC ambient temperature fluctuation

ASDA-B2 Series			100w	200w	400w	750w	1kw	1.5kw	2kw	3kw
			01	02	04	07	10	15	20	30
Torque Control Mode	Analog Input Command	Voltage Range	0 ~ ±10 VDC
		Input Resistance	10 KΩ
		Time Constant	2.2 μs
	Command Source		External analog signal / Internal parameters
	Smoothing Strategy		Low-pass filter
	Speed Limit		Set by parameters or via analog input
Analog Monitor Output			Monitor signal can set by parameters (Output voltage range: ±8 V)
Digital Input / Output	Input		Servo on, Fault reset, Gain switch, Pulse clear, Zero clamp, Command input reverse control, Torque limit, Speed limit, Speed command selection, Speed / position mode switching, Speed / torque mode switching, Torque / position mode switching, Emergency stop, Positive/negative limit, Forward / reverse operation torque limit, Forward/reverse JOG input, E-gear N selection, Pulse input prohibition
	Output		Encoder signal output (A, B, Z Line Driver / Z Open collector)
			Servo on, Servo ready, Zero speed, Target speed reached, Target position reached, Torque limiting, Servo alarm, Brake control, Early warning for overload, Servo warning
Protective Functions			Over current, Overvoltage, Under voltage, Overheat, Excessive speed deviation, Excessive position deviation, Encoder error, Emergency stop, Communication error, Short-circuit protection of terminal U, V, W and CN1, CN2, CN3
Communication Interface			RS-232 / RS-485
Environment	Installation Site		Indoor location (avoid direct sunlight), no corrosive liquid and gas (avoid oil mist, flammable gas, dust)
	Altitude		Altitude 1000 m or lower above sea level
	Atmospheric Pressure		86 kPa ~ 106 kPa
	Operating Temperature		0 ºC ~ 55 ºC (If operating temperature is above 45 ºC, forced cooling will be required)
	Storage Temperature		-20 ºC ~ 65 ºC (-4 ºF to 149 ºF)
	Humidity		0 to 90% (non-condensing)
	Vibration		Under 20 Hz, 9.80665 m/s2 (1G), 20 ~ 50 Hz 5.88 m/s2 (0.6 G)
	IP Rating		IP20
	Power System		TN System*3
	Certifications		UL, cUL, CE, and RoHS