Home > Products > Alnico magnet > Custom new design TS16949 RoHs high grade V Shape Sheets permanent Alnico 5 Bar Magnet
Custom new design TS16949 RoHs high grade V Shape Sheets permanent Alnico 5 Bar Magnet
- 1000 per Month
- T/T Credit Card
- Custom high quality round ring shape alnico speaker magnet with hole
- Permanent alnico block magnet 64x44.5x197
- Wholesale 5x13mm best quality cast permanent alnico Industrial sensor magnet manufacture
- Hot selling best quality cast permanent alnico Industrial sensor magnet
- Low price best quality cast permanent alnico Cow stomach sensor bar magnet
- China best quality cast permanent block magnet for Level gaugemanufacture
Product Description
Q:Motor has been running then fails to start,what to do?
A:Likely cause: Fuse or circuit breaker is tripped.
What to do: Replace the fuse or reset the breaker.
Likely cause: Armature is shorted. Motor may make a humming noise and the circuit breaker or fuse will trip.
What to do: Disassemble motor and inspect the armature for a burnt coil. Inspect the commutator for burnt bars. If this condition exists, the motor needs to be replaced.
Likely cause: The brushes may be worn down too far and no longer make contact with the commutator.
What to do: Check the brushes to make sure that they are still making contact with the commutator. Contact manufacturer for brushes.
Likely cause: Controller may be defective.
What to do: Verify voltage is coming out of the controller.
Q: On initial installation, motor fails to start up,what to do?
A: Likely cause: Motor is incorrectly wired
What to do: Verify that the motor is wired correctly.
Likely cause: No output power from controller.
What to do: Measure voltage coming from the controller.
Likely cause: Motor is damaged and the armature is rubbing against the magnets.
What to do: Disassemble motor and see if the armature can be realigned by reassembly. Motor may have to be replaced.
Q: Motor takes too long to accelerate,what to do?
A: Likely cause: Motor controller not properly set.
What to do: Adjust the acceleration trim pot of the controller.
Likely cause: Brushes are worn.
What to do: Verify brush length.
Likely cause: Bearings may be defective.
What to do: Inspect bearings. Noisy or rough bearings should be replaced.
Q: Motor runs in the wrong direction,what to do?
A: Likely cause: Incorrect wiring
What to do: Interchange the two motor leads.
Q: Motor runs OK but has a clicking noise,what to do?
A: Likely cause: Suspect a burr on the commutator.
What to do: Remove burr from commutator using a commutator stone.
Contact Us
- Ningbo Haofeng Magnet Technology Co., Ltd.
- China best quality cast permanent alnico bar Balance Magnet manufacture
- China 45x30x30mm best quality cast permanent alnico bar Magnet for Horseshoe Education manufacture
- Low price 62x3x12.3mm best quality cast permanent alnico bar magnet for Guitar pickup
- Hot sale best quality cast permanent alnico magnet for Welded parts
- Hot sale best quality cast permanent alnico magnet for Industrial use
- Factory hot selling best quality cast permanent alnico magnet permanent blocks for Industrial host
- Custom china supplier new design various shape super powerful cast strong alnico magnet
- 2020 Permanent alnico block magnet for education manufacture
- High quality best quality cast permanent alnico magnets permanent blocks for Industrial host manufacture
- custom OEM high quality low price different size various shape arc smco magnet
- Customized high grade Samarium super strong Cobalt SmCo Disc Magnets For Sale
- Custom magnets big block powerful magnetic blocks super strong cheap SmCo magnet for sale
- barium strong isotropic ferrite magnetic ceramic powder
- Custom factory different size tool available ceramic black various shapes grade C8 strong block ferrite magnet
- China manufacturer price 6cm type length irregular magnet rattlesnake egg ferrite magnets
- L47x5.75x6mm C8 Grade block ferrite magnets
- Ceramic Disc Magnets Round Fridge
- grade C8 strong magnet ferrite
- custom high quality ferrite magnet
- high quality ferrite magnet powder
- Custom high quality performance different size arc shape super strong y40 ferrite magnet with two hole
- custom high quality different size oval shape bullet shape neodymium funny ferrite magnet
- Custom magnet ferrite for rotor
- Wholesale Custom China Supplier Strongest High Quality Rubber Magnetr Ferrite Magnet Powder
Popular Searches
Find Similar Products By Category
- Minerals & Metallurgy > Magnetic Materials
- Buy on GoldSupplier.com
- How to Buy
- Browse by Catagories
- Browse by Hot Regoins
- Private Sourcing Events
- Sell on GoldSupplier.com
- How to Sell
- Post Products
- Manage Products
- Manage Groups
- About
- About Us
- Link to Us
- Contact Us
- Sitemap
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now-
sales
Welcome to my shop! Glad to serve you!Please send your question!
Your message has exceeded the limit.
Your message has exceeded the limit.
-
-
Your inquiry content must be between 20 to 5000 characters.Send Now.
-
Please input the mailbox.
-