long range wifi repeater sunhans eSunRC 5.8GHz 4W TX wifi signal booster for 5.8GHz wireless device extend WiFi signal range

SKU :0305SH200789

Model:SHPro58GTX4W

 1. [Simply plug and play]
Extend the range of your wireless network with the Indoor Wifi Booster Amplifier.

Plug and play connections,no software, no configuration and virtually no setup of software.

2. [Compatible with any 5.8G wireless device],used for transmit need (TX Only).
Our product can support 5.8G Hz WLAN 802.11a/n/ac,5.8G Hz wireless AP,

5.8G Hz wireless bridge,5.8GHz wireless router, 5.8GHz wireless network card, 5.8GHz wireless monitoring(NVR,DVR),

5.8GHz wireless microphone,RC drones,FPV device etc

3.[Maximum Output power].
The max output power can be up to 4000mW.

This amplfier will boost the transmit (TX Only) power of your wireless device a whopping 36dBm.

4.About the input power: 
(output power of the device = input power of the amplifier),

Sunhans SHPro58GTX4W booster input power 0~20dBm(18~19dBm will better),

if the output power of the device is greater than 20dBm or the power is relatively small -2~6dBm,kindly let us know,we will give the suggestion to solove this question according to your actual situation.

Technical Specifications

Booster model: SHPro58GTX4W

Operating range : 5000~5875MHz

Channel width: 20Mhz&40Mhz&80Mhz

Supported standards: IEEE 802.11a/n/ac

Operation mode: Bi-directional, half-duplex, time division duplex

Connector type: To radio SMA female (hole inside).

              To antenna RP-SMA female (pin inside)

Output power: 4000mW (36dBm)

Input power: 0 ~ 20dBm

Transmit gain: 17 ~ 20dB

Noise figure: ≤3.5dB typical

Frequency response: ±1dBoveroperatingrange

Power adapter: 5-16V/2A DC

Material: Cast aluminum

LED light: Power status LED and activity status LED

Booster weight: 59g
Booster size: 9.2*4.1*1cm

 Package contents

For UAV,Routers,IP cameras, R/C helicopters, planes and cars,Walkie talkies,ZigBee, Robot...
For House, Office,Hotels,Supermarkets, Hospitals,Parking Spaces...
For WiFi Solution & Project : WiFi Hotspot Solutions,Access points,Smart home systems, Smart city IOT, RC Drones Platform,security camera system ...

1.What is the WiFi signal booster? How can I connect the WiFi Signal Booster?

The working mode of the WiFi signal booster needs to be connected to the signal source (customer device which cause wifi signal ) through one end of the cable,

and the other end is connected to the antenna, and the WiFi signal range is expanded through the antenna.

2.Feature:

  a. Plug and play, no software setup.

  b.Wide application range, can enlarge WiFi signal coverage range, as long as the frequency of the product can be applied

3. How to find a suitable wifi signal booster?

Firstly , you need to know the frequency of your device. The frequency of a typical WiFi device is single frequency 2.4 GHz, 5.8 GHz; dual frequency 2.4 GHz and 5.8 GHz.
Depending on the frequency of the device, select the appropriate Sunhans booster.

Secondly , select the product with the corresponding power based on the distance that needs to be amplified. 
The larger the power of the amplifier, the larger the coverage.
For signal coverage should be equipped with an omnidirectional antenna ;

For long distance coverage should be equipped with an directional antenna. 
(For drone equipment, customers need to consider the endurance of the drone)

Thirdly, Need to know the output power of the device.
(output power of the device = input power of the amplifier) Sunhans booster input power 0~20dBm,

if the output power of the device is greater than 20dBm or the power is relatively small -2~6dBm,

you need to inform us, we will adjust it according to your actual situation.

4. Can I install the Sunhans booster myself?
Of course, our products are easy to install and plug and play, and the product package contains instructions for each product.

5. About LED lights.
A flashing green light indicates that the wifi signal booster is powered on.
Normal operation is a red light flashing green, indicating that the signal booster receives the signal from the device and sends a wifi signal.