Home > Products > IC > TPS54618QRTERQ1 switch regulator TI original from stock

Share|

TPS54618QRTERQ1 switch regulator TI original from stock

FOB Price:Negotiable |Get Latest Price
Min.Order Quantity:1 Piece / Pieces
Supply Ability:9000 Piece / Pieces per Month

Product Details

Brand Name:	TI	Place of Origin:	Albania	Model Number:	TPS54618QRTERQ1
Type:	Drive IC	Package:	9000	D/C:	22+

Packaging Details

3000

Product Description

Introduction

The TPS54618-Q1 device is a full-featured 6-Vin, 6-A, synchronous step-down current-mode DC-DC

converter with two integrated metal-oxide-semiconductor field-effect transistors (MOSFETs). The

TPS54618-Q1 device can operate in a wide range of switching frequencies from 200-KHz to 2-MHz. The

switching frequency can be set using a pulldown resistor or an externally applied signal at the RT pin as

shown in Figure 1. Refer to Interfacing TPS57xxx-Q1,TPS65320-Q1 Family, and TPS65321-Q1 Devices

With Low Impendence External Clock Drivers (SLVA755), for more information regarding interfacing an

external clock to TPS54618-Q1 family of devices.

The regulated output voltage at no load is given by Equation 1:

Vout = Vin × tON × fSW

where

•

Vin = input voltage

•

Vout = output voltage

•

tON = ON time

and

•

fSW = switching frequency

(1)

For given input and output voltages, as switching frequency is increased, tON will reduce. If tON falls below

the minimum value allowed by the internal circuit design, the output voltage may not track the internal 0.8-

V reference and would therefore not be regulated. To maintain the regulation at higher switching

frequencies, tON must be kept above a minimum value. If the switching frequency is less than or equal to

the data sheet maximum value of 2 MHz, tON will always be above designed minimum value and the

output would be regulated.

2.35-MHz Operation

Bench test and chip-level simulations were done to check whether the TPS54618-Q1 can remain in

regulation while switching at a frequency higher than 2.0 MHz.

The test conditions for the bench test and chip-level simulation were as follows:

•

Supply input voltage: 5.33 V

•

Regulated output voltage: 1.35 V

•

Operating switching frequency in bench setup: 2.35 MHz synchronized to an external clock as shown

in Figure 1.

Under these test conditions, the on time at a 100-mA load for the TPS54618-Q1 to maintain regulation

was verified by bench measurements to be 109.6 ns, compared to the value estimated by Equation 2:

(1.35 V / 5.33 V) × (1 / 2.35 MHz) = 107.8 ns

(2)

Minimum controllable on time at higher frequency and input voltage is verified to be less than 90 ns,

confirmed by the simulations in Section 3.

2.5-MHz Operation Simulation Results

A full chip breaking-point simulation is performed at 2.5-MHz clock frequency using the input and output

voltages specified in the following list to determine the minimum controllable tON allowed by internal circuit

design. The 2.5-MHz clock frequency is chosen to have some margin for oscillator tolerances and to be

sure that it works for 2.35-MHz clock frequency.

•

Input voltage swept from 5 V to 6 V

•

Output voltage programmed to 1.35 V

•

Load current set to 10 mA using a 135-Ω resistor

•

LOUT = 0.33 µH, COUT = 33 µF

•

RCOMP = 3.83 kΩ, CZERO = 1.5 nF, CPOLE = 0 pF

Simulation results:

•

Transient turn on behavior appears normal

Contact Us

Shenzhen nanbeihang Electronic Development Co., Ltd: Contactsiqi; Phone86-88377872-13714705290; AddressHuali building Shenzhen,Guangdong

Product Categories

Integrated circuit

power chip

Connector

New Products

TPS54618QRTERQ1 switch regulator TI original from stock

Product Details

Packaging Details

Product Description

Contact Us

Popular Searches

Find Similar Products By Category